Pokémon mini Development Documentation

LCD and LCD Driver

LCD screen

Taped to the plastic front with clear, double-sided 3 mm wide tape in a hollow rectangle shape, the rectangle being approx. 35.4mm x 27.6mm on the outside

The reflector is taped to the board with approx. 28mm (l) x 4mm (w) x 3.6mm (h) black foam tape

S1D15605 LCD driver

S1D15000 Series Technical Manual

The driver runs in parallel mode (P/S = HIGH), master operation (M/S = HIGH), with the internal oscillator circuit disabled (C/S = LOW). Thus the CL line takes input from the MCU via OSC1 and the FR line switching resets register $8A to 1 and increases $81’s frame counter by 1 (see page 8-29 for a diagram).

Commands

To simplify interaction with the LCD, try libpmdd instead of direct access.

LCD_CTRL is primarily used for sending commands to the LCD driver and is accessible through register $FE on the PM.

LCD_DATA is primarily used for sending display data to the LCD driver and is accessible through register $FF on the PM.

LCD_CTRL and LCD_DATA both write and read over the D0-D7 lines, it determines what operation is happening and whether CTRL or DATA is being read/written by the status of the A0, RD, & WR lines.

A0 RD WR R/W CTRL/DATA
0 0 1 Read CTRL
0 1 0 Write CTRL
1 0 1 Read DATA
1 1 0 Write DATA

Command list

Listed below are the commands, written to CTRL.

Cmd # Command Command Code Hex range
1 Display ON/OFF 1 0 1 0 1 1 1 x $AE - $AF
2 Display start line 0 1 a a a a a a $40 - $7F
3 Set Page 1 0 1 1 a a a a $B0 - $BF
4a Set Column HI 0 0 0 1 h h h h $10 - $1F
4b Set Column LO 0 0 0 0 l l l l $00 - $0F
8 ADC select 1 0 1 0 0 0 0 x $A0 - $A1
9 Invert 1 0 1 0 0 1 1 x $A6 - $A7
10 All on 1 0 1 0 0 1 0 x $A4 - $A5
11 LCD bias 1 0 1 0 0 0 1 x $A2 - $A3
12 Start RMW 1 1 1 0 0 0 0 0 $E0
13 End RMW 1 1 1 0 1 1 1 0 $EE
14 Reset 1 1 1 0 0 0 1 0 $E2
15 Row direction 1 1 0 0 x - - - $C0 - $CF
16 Power control 0 0 1 0 1 m m m $28 - $2F
17 V5 resistor ratio 0 0 1 0 0 r r r $20 - $27
18a Contrast 1 0 0 0 0 0 0 1 $81
18b Contrast - - v v v v v v $00 - $FF
19a Static indicator 1 0 1 0 1 1 0 x $AC - $AD
19b Static indicator - - - - - - m m $00 - $FF
20 Power saver    
21 NOP 1 1 1 0 0 0 1 1 $E3
22 Test 1 1 1 1 - - - - $F0 - $FF

Writing to display RAM

Writes the byte to display RAM at the current cursor location then increments the cursor by 1. When the cursor reaches the end of the current page, it does not wrap around to the next page, you must do this manually.

The data sent is displayed in a column of the current page formed as 0bABCDEFGH being (when rows are…)

Normal Reversed
H A
G B
F C
E D
D E
C F
B G
A H

Then moves one column to the right (if ADC is normal) or left (if ADC is reversed).

Reading display RAM

TODO: how to read reliably

Reading from LCD_DATA reads the byte in display RAM where the cursor is currently. If the driver is currently operating in RMW mode, the cursor is not incremented after reading. Otherwise, it is incremented.

TODO: does ADC reverse reading direction?

Reading display status

Read from LCD_CTRL. TODO: how to read reliably

The returned byte contains status information in the upper nibble:

FPC board connector pinout

Pins 1 and 29 are labeled on the board. In normal reading direction, 1 is on the left. The connector on the board is label CN3.

  1. VR
  2. V5
  3. V4
  4. V3
  5. V2
  6. V1
  7. CAP2-
  8. CAP2+
  9. CAP1-
  10. CAP1+
  11. CAP3- (mislabled as CAP3+ in the block diagram)
  12. VOUT
  13. VSS (GND)
  14. VDD (VCC)
  15. D7
  16. D6
  17. D5
  18. D4
  19. D3
  20. D2
  21. D1
  22. D0
  23. RD
  24. WR
  25. A0
  26. RES
  27. CS
  28. CL
  29. FR