
Original schematic by Tauwasser
For KiCad files for a newer version see here
For an interactive tracing tool see here
The console has a main board and also a daughter board which contains the voltage step-up circuit. Largely, the daughter board is not labeled. It connects to the LCD via a FPC, to the cartidge via the custom 33-pin connector, to the buzzer via two wires, and to the rumble motor via a pad which its terminals press against when the unit is closed.
The board has a marking located above the POWER contact which reads HGC0110-330010-xx where xx can be 01 or 02 which indicates the board revision. There is a marking to the bottom right of PAD1 reading Ax where x is some number, 8 on my JP 01 board but 4 on my US 01 board.
Printed above CN3 (move the black part into the locked position to see) is: √̅ᴛ 7 ▲ 94V-0 followed by a 4-digit number written in a 7-segment font. Nearby-ish (closer on 02 revision) is the UL Recognized mark.
We describe locations as either front (F) (screen-side) or back (B) (cart-side) and use the following abbreviations: top-left (TL), top-right (TR), middle-left (ML), middle-right (MR), bottom-left (BL), and bottom-right (BR).
When looking at the cart side, “left” is the negative end of the battery terminal and “top” is the side the cartridge enters. In this orientation the 1.5V on the battery image can be read correctly.
When looking at the screen side, “left” is where the LEFT contact is and “top” is where the IR blaster is. In this orientation all the button contact labels can be read correctly.

For terminals on a component, they’re described based on the orientation of the text on the silk-screen. Known components’ pins may be named.
Every label on the board is listed below but there may not be anything interesting to say about the component. To see all its connections, check the schematics instead.
The board has a revision marker printed above the POWER contact, at the end of the string.
The boards are largely the same but with some minor differences:
The A# (e.g. A4) printed under PAD1 is not a component label, but the purpose is unclear. The 0# (e.g. 02) printed next to the negative battery terminal is a copy of the final component of the identifier printed above the power contact (e.g. HC0110-330010-02). These examples are from the images above; in contrast my Japanese Wooper Blue unit has A8 and 01.
All capacitors on the main board, except for three of them, are surface mounted (SMD) multilayer ceramic capacitors (MLCC).
C1, C4, and C5 are all SMD cylindrical aluminum electrolytic capacitors with a capacitance of 100 μF. They’re 6.3mm diameter and ~4.5 mm tall.
| Label | Populated? | Location | Capacitance | Description |
|---|---|---|---|---|
| C1 | yes | B MR | 100 μF | electrolytic |
| C2 | yes | B MR, left of C1+ | ? | ceramic |
| C3 | yes | F ML, right of C4 | ? | ceramic |
| C4 | yes | F ML | 100 μF | electrolytic |
| C5 | yes | B ML | 100 μF | electrolytic |
| C6 | yes | F UL, below Q2 | ? | ceramic |
| C7 | yes | B ML, TL of U1 | ? | ceramic |
| C8 | yes | B BR, BR of U1 | ? | ceramic |
| C9 | 01-only | F UR, above U5 | ? | ceramic |
| C10 | yes | F MR, above R34 | ? | ceramic |
| C11 | yes | F ML, left of TP3 | ? | ceramic |
| C12 | yes | F ML, right of R2 | ? | ceramic |
| C13 | no | F ML, left of R9 | 30 pF (rec) | named CG2 in S1C88 TMs |
| C14 | no | F MR, right of Y2 | 30 pF (rec) | named CD2 in S1C88 TMs |
| C15 | yes | F MR, right of Y1 | ? | ceramic, named CG1 in S1C88 TMs |
| C16 | yes | B BL, between R7 & R11 | ? | ceramic |
| C17 | yes | F UR, right of R18 | ? | ceramic |
| C18 | yes | F UR, right of C17 | ? | ceramic |
| C19 | yes | B BR, above U2 | ? | ceramic |
| C20 | yes | F UR, below C21 | ? | ceramic |
| C21 | yes | F UR, BR of C25 | ? | ceramic |
| C22 | yes | F UR, right of C23 | ? | ceramic |
| C23 | yes | F UR, right of C18 | ? | ceramic |
| C24 | yes | F ML, above C4 | 1 μF | ceramic |
| C25 | yes | F UR, below C23 | 1 μF | ceramic |
| C26 | yes | F MR, above D3 | 1 μF | ceramic |
| C27 | yes | F MR, BR of CN3 | 1 μF | ceramic |
| C28 | yes | F UL, below L1 | ? | ceramic |
| C29 | yes | B ML, right of PAD2 | ? | ceramic |
| C30 | yes | B ML, BL of U1 | ? | ceramic |
| C31 | yes | B MR, right of CN4 | ? | ceramic |
| C32 | yes | B MR, under C31 | ? | ceramic |
| C33 | yes | F ML, left of C13 | ? | ceramic |
| C34 | no | F UR, below U5 | ? | - |
For more information on the LCD, see its main page
Connector slot for the FPC to the LCD, pins 1 (left) and 29 (right) are labeled.
Pin names are taken from the S1D15605 docs.
I/O listed from the perspective of the LCD. PS = Power Supply.
| Pin # | Name | I/O | Description |
|---|---|---|---|
| 1 | VR | I | Output voltage regulator terminal |
| 2 | V5 | PS | Liquid crystal drive power supply level 5 |
| 3 | V4 | PS | Liquid crystal drive power supply level 4 |
| 4 | V3 | PS | Liquid crystal drive power supply level 3 |
| 5 | V2 | PS | Liquid crystal drive power supply level 2 |
| 6 | V1 | PS | Liquid crystal drive power supply level 1 |
| 7 | CAP2- | O | DC/DC voltage converter1 |
| 8 | CAP2+ | O | DC/DC voltage converter1 |
| 9 | CAP1- | O | DC/DC voltage converter1 |
| 10 | CAP1+ | O | DC/DC voltage converter1 |
| 11 | CAP3- | O | DC/DC voltage converter1 |
| 12 | VOUT | I/O | DC/DC voltage converter1 |
| 13 | VSS | PS | Ground (GND) |
| 14 | VDD | PS | Shared with MPU power supply terminal VCC |
| 15 | D7 | I/O | Data bit 7 |
| 16 | D6 | I/O | Data bit 6 |
| 17 | D5 | I/O | Data bit 5 |
| 18 | D4 | I/O | Data bit 4 |
| 19 | D3 | I/O | Data bit 3 |
| 20 | D2 | I/O | Data bit 2 |
| 21 | D1 | I/O | Data bit 1 |
| 22 | D0 | I/O | Data bit 0 |
| 23 | RD | I | 0 = MPU is reading from D7~0 |
| 24 | WR | I | 0 = MPU is writing to D7~0 |
| 25 | A0 | I | 0 = status/control, 1 = display data |
| 26 | RES | I | Reset. When LOW, the settings are initialized |
| 27 | CS | I | Chip Select. When LOW, the data/command I/O is enabled |
| 28 | CL | I2 | The display clock input terminal |
| 29 | FR | O2 | The liquid crystal alternating current signal |
For more information on the cartridge, see its main page
Cartridge slot connector, pins 33 (left) and 1 (right) are labeled.
Pin names are largely from the community.
I/O listed from the perspective of the CPU. PS = Power Supply.
TODO: confirm voltage, is it really 3.3v ??
| Pin # | Card pin | Name | I/O | Description |
|---|---|---|---|---|
| 1 | B1 | VDD | PS | Stepped down from VCC |
| 2 | A1 | VDD | PS | Stepped down from VCC |
| 3 | B2 | A20 | O | Address bit 20 |
| 4 | A2 | A9 | O | Address bit 9 when LALE=high, 19 when HALE=high |
| 5 | B3 | A8 | O | Address bit 8 when LALE=high, 18 when HALE=high |
| 6 | A3 | A7 | O | Address bit 7 when LALE=high, 17 when HALE=high |
| 7 | B4 | A6 | O | Address bit 6 when LALE=high, 16 when HALE=high |
| 8 | A4 | A5 | O | Address bit 5 when LALE=high, 15 when HALE=high |
| 9 | B5 | A4 | O | Address bit 4 when LALE=high, 14 when HALE=high |
| 10 | A5 | A3 | O | Address bit 3 when LALE=high, 13 when HALE=high |
| 11 | B6 | A2 | O | Address bit 2 when LALE=high, 12 when HALE=high |
| 12 | A6 | A1 | O | Address bit 1 when LALE=high, 11 when HALE=high |
| 13 | B7 | A0 | O | Address bit 0 when LALE=high, 10 when HALE=high |
| 14 | A7 | VDD | PS | Stepped down from VCC |
| 15 | B8 | HALE | O | High address bits are latched when HALE is high |
| 16 | A8 | VDD | PS | No pad on cartridge |
| 17 | B9 | LALE | O | Low address bits are latched when LALE is high |
| 18 | A9 | GND | PS | Ground |
| 19 | B10 | D0 | I/O | Data bit 0 |
| 20 | A10 | D1 | I/O | Data bit 1 |
| 21 | B11 | D2 | I/O | Data bit 2 |
| 22 | A11 | D3 | I/O | Data bit 3 |
| 23 | B12 | D4 | I/O | Data bit 4 |
| 24 | A12 | D5 | I/O | Data bit 5 |
| 25 | B13 | D6 | I/O | Data bit 6 |
| 26 | A13 | D7 | I/O | Data bit 7 |
| 27 | B14 | OE | O | Output Enable. Reading data when OE is high |
| 28 | A14 | IRQ | I | Causes Cartridge IRQ when IRQ is high |
| 29 | B15 | WE | O | Write Enable |
| 30 | A15 | CS | O | Chip Select |
| 31 | B16 | CARD_N | I | Card detect. Active-low. Connected to GND in the cartridge |
| 32 | A16 | GND | PS | Ground |
| 33 | B17 | GND | PS | Ground |
For more information on the keypad, see its main page
The keypad uses contacts under a likely silicone membrane with a carbon coating on the bottom bridging them to ground. The C button is SW1 rather than one of these.
The top-left and bottom-right contact points are GND while the other connects to the CPU and TP1.
The top-left and bottom-right contact points are GND while the other connects to the CPU.
The top-left and bottom-right contact points are GND while the other two connect to the CPU and TP2.
The top-left and bottom-right contact points are GND while the other two connect to the CPU, U5, and the LCD.
The right contact point is GND while the other connects to the CPU.
The top contact point is GND while the other connects to the CPU.
The bottom contact point is GND while the other connects to the CPU.
The left contact point is GND while the other connects to the CPU.
Located screen-side, below C4. Anode top.
Located screen-side, right of R5. Anode left.
A SOT23 diode, possibly 1SS226 (TODO: confirm). Same chip as D4
Located screen-side, middle-right. 3-pin AKC (pins labeled).
Same chip as D3
Located cart-side, above C5. 3-pin AKC (pins labeled).
Located screen-side, bottom-right. Anode top.
Located screen-side, bottom-right. Anode top.
Fuse 1. Located cart-side, bottom-right of C2.
why
The left contact (labeled 2) is GND. This pad connects the rumble motor mounted in the back of the case to the system.
For more on how to use the rumble motor, see here
A 2-pin spring contact ERM vibration motor contained in a light gray silicone sleeve which can be slipped off with some trouble, inserted into the case back without glue.

Pin 1 connects BZ through a red wire to the inner circle (top electrode) of the speaker. Pin 2 connects BZ- through a black wire to the outer circle (metal plate).
For more information, see its main page
~20 mm diameter piezo buzzer with ~15 mm inner diameter (incl. ring). It’s glued to the back casing. Thickness unknown.
A SOT89-3 transistor, possibly 2SJ361 (TODO: confirm).
This detects the CART_POW_EN signal and steps down the VCC to input into the cartridge bus.
A SOT89-3 transistor, possibly 2SA1419 (TODO: confirm).
This powers the rumble motor when Q3 closes.
A SOT323 transistor, possibly 2SC4155 (TODO: confirm).
This detects the RUMBLE signal, connecting Q2 to GND.
R41 and R42 pads do not exist on the 01 board.
R9 is named Rf in the S1C88 technical manuals.
| Label | Populated? | Location | Resistance |
|---|---|---|---|
| R1 | yes | F TL, between Q3 & Q1 | 1 kΩ |
| R2 | no | F ML, above RV1 | ? |
| R3 | yes | F TL, BL of Q1 | 100 Ω |
| R4 | yes | F TL, BL of Q3 | 10 kΩ |
| R5 | yes | F TL, right of R4 | 100 kΩ |
| R6 | yes | B BR, right of R10 | 200 Ω |
| R7 | yes | B BL, left of C16 | 33 Ω |
| R8 | yes | F TR, below C20 | 68 kΩ |
| R9 | yes | F ML, left of Y2 | 1 MΩ |
| R10 | yes | B BR, below U1 | 10 kΩ |
| R11 | no | B BL, below U1 | ? |
| R12 | yes | B TL | 1 kΩ |
| R13 | yes | B ML, BL of D4 | 100 Ω |
| R14 | yes | F MR, below D3 | 100 Ω |
| R15 | yes | F MR, below R34 | 500 kΩ |
| R16 | yes | B BR, TL of U2 | 1 kΩ |
| R17 | yes | B BR, below U2 | 10 kΩ |
| R18 | yes | F TR, BR of U4 | 33 Ω |
| R19 | yes | F TL, below R20 | 100 kΩ |
| R20 | yes | F TL, below U4 | 11 Ω |
| R21 | yes | F TL, below R25 | 270 kΩ |
| R22 | yes | F TL, below R21 | 1.3 MΩ |
| R23 | yes | F ML, BR of Q1 | 33 Ω |
| R24 | yes | F ML, below R23 | 33 Ω |
| R25 | yes | F TL, below R26 | 33 Ω |
| R26 | yes | F TL, below R27 | 33 Ω |
| R27 | yes | F TL, below R28 | 33 Ω |
| R28 | yes | F TL, below R4 | 33 Ω |
| R29 | yes | F TL, below D2 | 33 Ω |
| R30 | yes | F TL, below R29 | 33 Ω |
| R31 | yes | F MR, left of R32 | 33 Ω |
| R32 | yes | F MR, BL of C27 | 33 Ω |
| R33 | yes | F ML, right of TP3 | 33 Ω |
| R34 | yes | F MR, BR (01)/below (02) C10 | 33 Ω |
| R35 | yes | F ML, right of R33 | 33 Ω |
| R36 | yes | F ML, right of R35 | 33 Ω |
| R37 | yes | F ML, right of R40 | 33 Ω |
| R38 | yes | F MR, right of R39 | 100 kΩ |
| R39 | no | F MR, right of C10 | ? |
| R40 | yes | F ML, right of R36 | 500 kΩ |
| R41 | 02-only | F MR, right of R42 | ? |
| R42 | 02-only | F MR, right of C27 | 0 Ω |
Located screen-side, middle left, right of C3.
The cartridge slot shield. Located cart-side, top. Has a long indented line with round caps in the center (but slightly below middle) of the bottom rectangle. The top has unevenly rounded edges and has two semi-circles indented along the top edge, placed 9.5 mm from either side.

For more information on the C button, see the keypad page
A 2-pin right-angle push button switch with grounded shield. Located cart-side, top left.
The top pin is GND and the bottom connects to the CPU.

For more on how to use the shock sensor, see here
A 2-pin enclosed reed switch (TODO: confirm type). Located cart-side, bottom left.
The pins are labeled, pin 1 is signal and pin 2 is GND.

Tests the A contact. Located cart-side, bottom left.
Tests the POWER contact. Located cart-side, bottom left. Next to it reads (PON#) possibly meaning “power on”
Tests if cartridge can be detected. Located screen-side, middle left. A label reading (CARD_N) has an arrow pointing to it; this is the name of the line it’s testing.
Tests the IrDA’s TXD line. Located screen-side, top center.
Tests the IrDA’s RXD line. Located screen-side, top center.
The voltage step-up converter daughter board. Located cart-side, center.
The board itself is 23 x 10 mm, likely ~1 mm thick.
Basically no component is labeled and no schematic has been made so all I can document is the package types.

The pins are not labeled, so instead we use the numbers and names from Tauwasser’s schematic.
I/O listed from the perspective of U1. PS = Power Supply.
| Pin # | Name | I/O | Location | Description |
|---|---|---|---|---|
| 1 | VIN | PSI | bottom right | Battery power in |
| 2 | VOUT | PSO | top right | VCC out |
| 3 | ? | I | top left | Connects to POW_? pin of U3 |
| 4 | GND | PS | bottom left | Ground |
| 5 | ? | I | bottom center | Connects to POWER contact |
A 24xx64-alike TSSOP-8 package EEPROM. Located cart-side, bottom right.
Pins 1-4 (left) and 7 (right) are wired to GND.
I/O listed from the perspective of the EEPROM. PS = Power Supply.
| Pin # | Name | I/O | Description |
|---|---|---|---|
| 1 | A0 | I | Address bit 0 |
| 2 | A1 | I | Address bit 1 |
| 3 | A2 | I | Address bit 2 |
| 4 | GND | PS | Ground |
| 5 | SDA | I/O | Serial data I/O |
| 6 | SCL | I | Serial clock input |
| 7 | WP | I | Write protect |
| 8 | VCC | PS | Power supply |
Other I2C devices, such as a DS1621 digital thermometer, can be wired to the SDA/SCL lines of the EEPROM chip to add them to the bus.

For more information on the CPU, see its main page
The S1C88V20 with glob top. Locate screen-side, middle center.
The name for this chip comes from Epson’s S1C88 tooling, which contains a memory layout of this name as well as debugger modules of this name.
The pins are not labeled, so instead we use the numbers and names (largely) from Tauwasser’s schematic. A few names come from other official specifications, CARD_N and most of the keypad are labeled on the board elsewhere.
I/O listed from the perspective of the CPU. PS = Power Supply.
| Pin # | Name | I/O | Description |
|---|---|---|---|
| 1 | VCC | PS | VCC (3v) |
| 2 | OSC3 | I | Connects to Y2 |
| 3 | OSC4 | O | Connects to Y2 |
| 4 | CAP | ? | Connects to C33 |
| 5 | GND | PS | Ground |
| 6 | OSC1 | I | Connects to Y1 |
| 7 | OSC2 | O | Connects to Y1 |
| 8 | CAP | ? | Connects to C16 |
| 9 | POW_? | O | Connects to U1 |
| 10 | VCC | ? | VCC (3v) |
| 11 | RESET | I | RESET contact input |
| 12 | OPT | ? | ? |
| 13 | POWER | I | POWER contact input |
| 14 | RIGHT | I | RIGHT contact input |
| 15 | LEFT | I | LEFT contact input |
| 16 | DOWN | I | DOWN contact input |
| 17 | UP | I | UP contact input |
| 18 | C | I | SW1 input |
| 19 | B | I | B contact input |
| 20 | A | I | A contact input |
| 21 | CARD_POW_EN | O | Enable power to the cartridge |
| 22 | BZ- | O | Inverted buzzer signal |
| 23 | BZ | O | Buzzer signal |
| 24 | GPIO6 | I/O | SHOCK |
| 25 | GPIO5 | I/O | Powers down U4 when high |
| 26 | GPIO4 | I/O | Enables rumble motor |
| 27 | GPIO3 | I/O | Connects to U2's SCL |
| 28 | GPIO2 | I/O | Connects to U2's SDA |
| 29 | GPIO1 | I/O | Connects to U4's TXD |
| 30 | GPIO0 | I/O | Connects to U4's RXD |
| 31 | LCD_FR | I/? | Connects to CN3's FR |
| 32 | LCD_CL | ?/O | Connects to CN3's CL |
| 33 | VCC | ? | VCC (3v) |
| 34 | GND | ? | Ground |
| 35 | LCD_CS | O | Select LCD for bus communication |
| 36 | LCD_WR | O | Connects to CN3's WR |
| 37 | LCD_RD | O | Connects to CN3's RD |
| 38 | LCD_A0 | O | Connects to CN3's A0 |
| 39 | D7 | I/O | Data bit 7 for CN3 & CN4 |
| 40 | D6 | I/O | Data bit 6 for CN3 & CN4 |
| 41 | D5 | I/O | Data bit 5 for CN3 & CN4 |
| 42 | D4 | I/O | Data bit 4 for CN3 & CN4 |
| 43 | D3 | I/O | Data bit 3 for CN3 & CN4 |
| 44 | D2 | I/O | Data bit 2 for CN3 & CN4 |
| 45 | D1 | I/O | Data bit 1 for CN3 & CN4 |
| 46 | D0 | I/O | Data bit 0 for CN3 & CN4 |
| 47 | HALE | O | High address latch enable (CN4) |
| 48 | LALE | O | Low address latch enable (CN4) |
| 49 | A0 | O | Address bit 0/10 (CN4) |
| 50 | A1 | O | Address bit 1/11 (CN4) |
| 51 | A2 | O | Address bit 2/12 (CN4) |
| 52 | A3 | O | Address bit 3/13 (CN4) |
| 53 | A4 | O | Address bit 4/14 (CN4) |
| 54 | A5 | O | Address bit 5/15 (CN4) |
| 55 | A6 | O | Address bit 6/16 (CN4) |
| 56 | A7 | O | Address bit 7/17 (CN4) |
| 57 | A8 | O | Address bit 8/18 (CN4) |
| 58 | A9 | O | Address bit 9/19 (CN4) |
| 59 | A20 | O | Address bit 20 (CN4) |
| 60 | OE | O | CN4's data Output Enable |
| 61 | WE | O | CN4's Write Enable |
| 62 | CS | O | Select cartridge for bus communication |
| 63 | CARD | I | Cartridge detect input |
| 64 | CN4-28 | I | Cartridge IRQ input |
For more information, see its main page
The IrDA blaster. As of yet unidentified. Located screen-side, top center.
It’s surrounded by a ~0.5mm thick rubber tape, exposing only the LEDs. The tape is essentially a rectangle with two corners cut out to allow it to bend around the casing.

It has a plastic cover over it that slots into the front shell. Two screws screw through the board, holes of this shield on the side, and into the front shell.

The pins are not labeled but are known based on the standardized pinout.
I/O listed from the perspective of the IR blaster. PS = Power Supply.
| Pin # | Name | I/O | Description |
|---|---|---|---|
| 1 | GND | PS | Ground |
| 2 | NC | - | Not connected |
| 3 | VCC | PS | VCC |
| 4 | GND | PS | Ground |
| 5 | PWDOWN | I | Power-down control |
| 6 | RXD | O | Receive data |
| 7 | TXD | I | Transmit data |
| 8 | LEDA | PS | LED anode |
4-pin voltage detector in a SC-82AB package. As of yet unidentified. Has a line on the left indicating the side with pin 1 followed by the text EDN (on my Japanese unit). Located screen side, top right, slightly BR of CN3.
The pin numbers here follow the designations for the SC-82AB package type where the wider pin (bottom right on 01, bottom left on 02) is pin 2. It’s possible that NC is a disconnected CE pin as that’s common enough on these components, but it’s untested.
| Pin # | Name | Description |
|---|---|---|
| 1 | VOUT | Connected to SYS_RESET |
| 2 | VIN | VCC |
| 3 | NC | Not connected |
| 4 | GND | Ground |
For more information, see OSC1
This is a low-power 32.768 kHz crystal resonator (passive oscillator) notably used for maintaining the real-time clock, but is also used elsewhere. This is named X'tal1 in the S1C88 technical manuals.
It does have a marking but it may not be visible; it’s an engraved text KDS followed by a number representing the final digit of the year it was printed in then a letter representing the month (A for January up to M for December (it skips I)). It’s not a surface-mount component, but is glued down.
This component is non-polarized so the pins don’t have names or numbers as it can go either way. Here we list them relative to the board.
| Pin | Connection |
|---|---|
| Top | OSC2 |
| Bottom | OSC1 |
For more information, see OSC3
This is the high-speed 4.00 MHz ceramic resonator (passive oscillator) used for the general purpose timers, communicating with the system bus and I/O, and clocking the CPU during normal operation. Because it’s using a ceramic oscillator for Y2 this is either named Ceramic or CR in the S1C88 technical manuals.
This oscillator has text printed on the top which looks like a curved M in a box followed by 4.00 and then a single-character serial such as L or J. It is a surface-mount component.
These specs are unfortunately from the 2009 datasheet, when ideally we would like a 2001 datasheet.
This component is non-polarized so the pins don’t have names or numbers as it can go either way. Here we list them relative to the board.
| Pin | Connection |
|---|---|
| Left | OSC3 |
| Middle | GND |
| Right | OSC4 |